SlipGrip Riser Plates

SlipGrip Riser Plates fit onto the vertical part of the step in order to ensure a fully anti slip solution to your slippery steps.

Stock Code:SGRP600B

Why Choose SlipGrip Riser Plates?


  • Suitable for - restaurants & nightclubs, communal areas in social housing, offices, leisure centres, shopping malls, sporting venues and more.
  • Quick and easy installation - simply glue into place with the supplied glue.
  • Easy maintenance and easy to clean - just wipe clean with warm, soapy water. This is a major benefit against painted risers that need to be sanded and repainted regularly.
  • Aesthetically pleasing - the riser plates cover the existing riser, thus complementing the look of the stairs and visually transforming existing stair cases.

How to Install

  • You can install our SlipGrip Riser Plates easily and quickly with the adhesive glue supplied with the product.



  • Ensure that the area is clean, dry and free from loose and friable material. Any “dished” or damaged surface areas should be patch repaired to provide a reasonably flat and consistent surface. You can patch repair concrete with our SlipGrip Step Edge Repair.

  • Dry fit riser plates to ensure they fit freely and that they sit flat down on the surface. If required, SlipGrip can be trimmed on site to suit, ideally using a skill saw with a 4mm diamond blade or an angle grinder with a 1mm blade.

  • Please ensure that goggles and gloves are worn at all times when any form of cutting is involved.


Adhesive Application

  • Ensure you apply the riser plates before you fit any of the stair treads. Apply an approx. 6mm bead (this may need to be increased dependant on the substrate conditions) of the high strength gap filling adhesive around the periphery of the underside of the riser plates approx. 25mm in from the edges. Then, starting from the bottom left corner come up at an angle (approx. 200mm across) and then down at an angle, to create a ‘peak and a trough’, repeat this until you reach the end.

  • Immediately press the panel firmly to the substrate to ensure adequate transfer of adhesive (depending on the size of the bead, this will elevate the sheet by approximately 1-1.5mm). A firm bond will be achieved in about one hour under normal circumstances and conditions.

  • Drill two holes on each side of the SlipGrip stair tread cover, the first approximately 15mm in from the back edge and 15mm from the side. The second one should again be approximately 15mm from the side and approx. 10mm back from the contrasting nosing (55mm) For larger treads, it may be necessary to have further fixing points in the centre of the tread.

  • If the substrate is in bad condition, screws are also recommended to fully secure the risers.

Technical Data Sheet

Mechanical Data Sheet




  • Lengths: 600mm, 750mm, 800mm, 1000mm, 1200mm, 1500mm, 2000mm or 3000mm
  • Height: 145mm
  • Thickness: 4mm


  • Black

Prices shown are excluding VAT. Please note this is an all day courier delivery service and is not guaranteed. Please refer to point 6 of our terms and conditions for full details.


Order Value United Kingdom Mainland
£100 and under £9.95
£100.01 to £300 £16.00
£300.01 to £500 £25.00
£500.01 to £750 £35.00
£750.01 to £1000 £42.00
£1001.01 to £1500 £52.00
£1500.01 to £2000 £67.00
£2000.01 to £3000 £95.00
£3000.01 to £4000 £120.00
£4000.01 and over £300.00


Order Value Highlands and Islands*
£100 and under £45.00
£100.01 to £500 £100.00
£500.01 to £1000 £200.00
£1000.01 to £3000 £280.00
£3000.01 and over £300.00


Order Value Europe Zone 1 & Northern Ireland**
£100 and under £45.00
£100.01 to £3000 £150.00
£3000.01 to £6000 £250.00
£6000.01 and over Please call 01440 712722 for a bespoke quote.


* Highlands and Islands include - the Scottish Highlands and Islands, Isle of Wight, Isle of Man and the Channel Islands. ** Countries included in Europe Zone 1 - Southern Ireland, France, Germany, Luxembourg, Netherlands & Belgium. For all deliveries outside Europe Zone 1, please call 01440 712722 to place your order.